Colorbond Fencing

Steel boundary fencing specified for salt air and bayside wind

Colorbond Fencing in Birkdale and Eastern Brisbane

Colorbond is the fence people choose when they're done maintaining one. No painting, no palings working loose, no rot at ground level. Sheets slot into rails between posts, the whole thing goes up fast, and it stays looking the same for twenty years. Across the newer estates through Thornlands, Birkdale and Victoria Point it's now more common than timber.

There is one thing that genuinely changes the spec out here, and it's distance from the water. Colorbond's steel substrate is protected by a zinc-aluminium coating and a baked-on paint finish, and that holds up well inland. Within a few hundred metres of Moreton Bay the salt load is higher, and the detail that matters is keeping the bottom edge of the sheet out of wet soil and leaf litter. That's what a concrete plinth does, and on a bayside job we'll usually recommend one rather than running the sheets down into the dirt.

Wind is the other factor. An exposed boundary at Wellington Point or Manly catching a south-easterly puts real load on a fence, and a 1.8m Colorbond run is effectively a sail. Post spacing and footing depth are what carry that load. We don't stretch post centres to save on materials, because a fence that flexes in a blow will have loose sheets within a season.

What Colorbond Gets You

Nothing to paint, stain, oil or re-nail
Won't rot, warp or get eaten by termites
Australian-made steel with manufacturer warranty on the coating
Full privacy with no gaps opening up as timber would
Non-combustible, which matters on the bushland-adjacent blocks
Goes up quickly, so your yard is open for less time
A colour range that doesn't fade out like painted timber does

Options and Configurations

Standard Boundary Fence

1.8m sheets between posts, the usual dividing fence. Available down to 1.2m for front boundaries and up to 2.1m where you need extra screening from a two-storey neighbour or a road.

Concrete Plinth Base

A concrete sleeper laid along the bottom of the fence line. Holds back garden beds and mulch, keeps the steel out of wet soil, and gives you a clean mowing edge. On sloping blocks it's also how you level out the run without leaving gaps underneath.

Lattice and Extension Tops

A decorative or slatted section added above the standard sheet height. Useful when a new build next door has sightlines straight into your yard and you need another 300 to 600mm without rebuilding the whole fence.

Stepped Runs for Slopes

Colorbond sheets are rectangular and can't be raked, so slopes are handled by stepping each bay down. Set out carefully with plinths filling the triangles, a stepped run looks deliberate. Set out badly it looks like a mistake, so we spend the time on the levels.

Matching Gates

Pedestrian and double gates in the same sheet profile and colour, so the gate reads as part of the fence rather than an afterthought. See our gates page for automation and driveway options.

Colour Selection

The full Colorbond range is available. Basalt, Monument and Wallaby are what most people land on around here; the paler colours show bayside dust and salt film sooner. We bring samples so you're choosing against your actual house rather than a screen.

Where We Install It

Dividing fences on new estates through Birkdale, Thornlands and Victoria Point
Replacing timber fences that have rotted or come down in a storm
Road-facing boundaries where traffic noise is a factor
Commercial and industrial yards around Capalaba and Tingalpa
Boundaries with plinths holding back terraced garden beds
Long runs on acreage where speed of installation matters

Common Questions

Will Colorbond rust this close to the bay?

The sheet itself holds up well; the risk is at the bottom edge where cut steel sits against damp soil, mulch or leaf litter. That's exactly why we push for a concrete plinth on bayside jobs and why we keep the fence line clear of garden beds piled against it. Done that way, a Colorbond fence at Wellington Point will long outlast a timber one in the same spot.

How does it handle a strong south-easterly?

Fine, if the posts and footings were specified for it. The sheets themselves are rigid; wind load goes into the posts. On exposed boundaries we tighten post spacing and go deeper on the footings rather than building to the minimum. The fences that fail in a blow are almost always the ones where post centres were stretched to shave the quote.

Can it be installed on a sloping block?

Yes, but it steps rather than rakes. Each bay sits level and drops at the post, and the triangular gap underneath gets filled with a concrete plinth or sleeper. On a gentle fall this looks good. On a steep fall it can look busy, and we'll tell you honestly if raked timber would suit the block better.

Is it dearer than timber?

Usually a bit more up front, and less over the life of the fence because there's no painting or paling replacement. If you're splitting the cost with a neighbour, bear in mind a standard sufficient fence under Queensland law doesn't have to be Colorbond, so the party wanting the upgrade often covers the difference. We can quote both for that conversation.

What happens if a sheet gets damaged later?

Individual sheets can be replaced without pulling the fence apart, which is one of the quieter advantages of the system. Worth noting the colour you choose now, because matching a ten-year-old faded sheet to a brand new one is easier if you know what it started as.

Can you do a pool fence in Colorbond?

A solid Colorbond barrier can be compliant, but you lose sight of the pool entirely, which most people regret. For pool barriers we'd point you at aluminium or glass instead, and keep Colorbond for the boundary.

Long Run to Cover?

We've got the crew to put up a full acreage boundary in days, not weeks, and an excavator for the footings.

Get in Touch